List of Modbus Registers

30001

0

0x00

VERSION AND MODULE TYPE

Read-only

Firmware version and module type (30001)

30004

3

0x03

RS485 COUNTER OF RECEIVED FRAMES

(32 bits)

Read-only

Counter of received messages (30004)

Default state is 0

Reset at the unit start and change of transmission parameters

30006

5

0x05

RS485 COUNTER OF FRAMES WITH ERROR

(32 bits)

Read-only

Counter of error messages (30006)

Default state is 0

Reset at the unit start and change of transmission parameters.

30008

7

0x07

RS485 COUNTER OF SENT FRAMES
(32 bits)

Read-only

Counter of sent messages (30008)

Default state is 0

Reset at the unit start and change of transmission parameters.

30017

15

0x0F

STATUS OF SPECIAL INPUTS

WORKING AS DIGITAL INPUT

Read-only

Status of special inputs working as digital inputs are represented by bits 0 and 1 in register (30017)

40001

0

0x00

VERSION AND MODULE TYPE PLUS ENABLE OF ACTIONS

Read&Write

Firmware version and module type plus enable of actions

40018

17

0x11

STATE OF DIGITAL OUTPUTS

Read&Write

State of digital outputs (40018)

40020

19

0x12

SPECIAL INPUTS COMMAND REGISTER

Read&Write

Special inputs command register (40020)

40021

20

0x14

SPECIAL INPUTS BLOCKING

Read&Write

Special inputs blocking (40021)

By default set to 0

40022

21

0x15

COUNTER RESET

Read&Write

Resetting counters value (40022)

Set bit in register to reset corresponding counter

40023

22

0x16

COUNTER 1 LSB

Read&Write

Memory

32-bit counters for each special input counting pulses.

40024

23

0x17

COUNTER 1 MSB

40025

24

0x18

COUNTER 2 LSB

Read&Write

Memory

40026

25

0x19

COUNTER 2 MSB

30071

70

0x46

SPECIAL INPUT 1 VOLTAGE

Read-only

Special input measure voltage 1-2 (30071, 30073) and

Special Input measure temperature 1-2 (30072, 30074)

Voltage measurement value is expressed in mV.

For current measurements, the formula for the current:

where: U – register value,

500 – value of attached resistance

Temperature is expressed in Celsius degrees * 10

For a result, divide the registry value by 10:

Selection of the type sensor is done using registers from 40151 to 40152 for each input separately

30072

71

0x47

SPECIAL INPUT 1 TEMPERATURE

Read-only

30073

72

0x48

SPECIAL INPUT 2 VOLTAGE

Read-only

30074

73

0x49

SPECIAL INPUT 2 TEMPERATURE

Read-only

30087

86

0x56

SPECIAL INPUT 1 VOLTAGE

Read-only

30088

87

0x57

SPECIAL INPUT 2 VOLTAGE

Read-only

30095

94

0x5E

SPECIAL INPUT TEMPERATURE 1

Read-only

30096

95

0x5F

SPECIAL INPUT TEMPERATURE 2

Read-only

30103

102

0x66

RESISTIVE INPUT 1 LSB

Read-only

Special input resistance measurement 1-2 (30103-30104, 30105-30106)

Resistance measurement result is expressed in Ω.

30104

103

0x67

RESISTIVE INPUT 1 MSB

Read-only

30105

104

0x68

RESISTIVE INPUT 2 LSB

Read-only

30106

105

0x69

RESISTIVE INPUT 2 MSB

Read-only

40134

133

0x85

MODBUS PROTOCOL TYPE

Read&Write

Memory

RS485 Modbus protocol type

0 - RTU, 1 - ASCII

40136

135

0x87

RS485 BAUD RATE

Read&Write

Memory

RS485 baud rate (40136)

40137

136

0x88

RS485 STOP BITS

Read&Write

Memory

Stop bits (40137)

Supported values are 1 and 2

The default value is 1

40138

137

0x89

RS485 DATA BITS

Read&Write

Memory

Data bits (40138)

Supported values are 7 and 8

The default value is 7

40139

138

0x8A

RS485 PARITY BIT

Read&Write

Memory

Parity bit (40139)

The default value is 0 (no parity)

Allowed values:

40140

139

0x8B

RESPONSE DELAY

Read&Write

Memory

Response delay time (40140)

Delay in ms before sending response

The default value is 0

40141

140

0x8C

WATCHDOG TIME

Read&Write

Memory

Watchdog time (40141)

Time in seconds before watchdog reset in case of no transmission

Setting value of 0 disables the watchdog

The default value is 15 s

40143

142

0x8E

DEFAULT STATE OF DIGITAL OUTPUTS

Read&Write

Memory

Default state of digital outputs (40143)

State of digital outputs assigned at the start of the module and watchdog reset

The default value is 0

40151

150

0x96

SPECIAL INPUT 1 CONFIGURATION

Read&Write

Memory

Configuration of special input and type of temperature sensor

The default value is 1

40152

151

0x97

SPECIAL INPUT 2 CONFIGURATION

Read&Write

Memory

40159

158

0x9E

FILTER TIME CONSTANT

OF THE SPECIAL INPUT 1

Read&Write

Memory

Filter time of the special input 1-2 (40159-40160)

Filter time constant, expressed in seconds in the range from 0 to 60 seconds

The default value is 2 s, setting to 0 s disables the filter

40160

159

0x9F

FILTER TIME CONSTANT

OF THE SPECIAL INPUT 2

Read&Write

Memory

40176

175

0xAF

SPECIAL INPUT 1 CONFIGURATIO MODE

Read&Write

Memory

TIME VALUE [ms]

40177

176

0xB0

SPECIAL INPUT 1 TIME VALUE

Read&Write

Memory

40180

179

0xB3

SPECIAL INPUT 2 CONFIGURATIO MODE

Read&Write

Memory

40181

180

0xB4

SPECIAL INPUT 2 TIME VALUE

Read&Write

Memory

40242

241

0xF1

RADIO TX POWER

Read&Write

Memory

40243

242

0xF2

RADIO CHANNEL

Read&Write

Memory

Radio channel (40243)

40244

243

0xF3

RADIO BAUD RATE

Read&Write

Memory

Radio baud rate (20249)

40249

248

0xF8

RADIO AESKEY D1-D0

Read&Write

Memory

Radio transmission 128 bit encryption key (40249-40256)

Default values:

1111 2222 3333 4444 5555 6666 7777 8888

40250

249

0xF9

RADIO AESKEY D3-D2

Read&Write

Memory

40251

250

0xFA

RADIO AESKEY D5-D4

Read&Write

Memory

40252

251

0xFB

RADIO AESKEY D7-D6

Read&Write

Memory

40253

252

0xFC

RADIO AESKEY D9-D8

Read&Write

Memory

40254

253

0xFD

RADIO AESKEY D11-D10

Read&Write

Memory

40255

254

0xFE

RADIO AESKEY D13-D12

Read&Write

Memory

40256

255

0xFF

RADIO AESKEY D15-D14

Read&Write

Memory

40257

256

0x0100

RADIO COUNTER OF RECEIVED FRAMES

(32 – bits)

Read&Write

Memory

Counter of received messages (30004)

Default state is 0

Reset at the unit start and change of transmission parameters

40259

258

0x0102

RADIO COUNTER OF ERROT FRAMES (32 – bits)

Read&Write

Memory

Counter of error messages (30006)

Default state is 0

Reset at the unit start and change of transmission parameters

40261

260

0x0104

RADIO COUNTER OF TRANSMITTED FRAMES (32 – bits)

Read&Write

Memory

Counter of sent messages (30008)

Default state is 0

Reset at the unit start and change of transmission parameters

40263 - 40390

262 - 389

0x0106 – 0x0185

WIRELESS DEVICE STATUS 1 ÷ 128

Read-only

Bit 7: 0 - Int8 RX POWER [dBm]

Bit 8: 0 - Down; 1 - Ok