Module Registers | iC Knowledge Base

Registered Access

Modbus	Dec	Hex	Register Name	Access	Description
30001	0	0x00	Version/Type	Read	Version and type of the device
30002	1	0x01	Switches	Read	Switches state
40003	2	0x02	Baud Rate	Read/write	RS485 baud rate
40004	3	0x03	Stop Bits & Data Bits	Read/write	No. of stop bits & data bits
40005	4	0x04	Parity	Read/write	Parity bit
40006	5	0x05	Response Delay	Read/write	Response delay in ms
40007	6	0x06	Modbus Mode	Read/write	Modbus Mode (ASCII or RTU)
40009	8	0x08	Watchdog	Read/write	Watchdog
40033	32	0x20	Received Packets LSR (Least Significant Register)	Read/write	No. of received packets
40034	33	0x21	Received Packets MSR (Most Significant Register)	Read/write	No. of received packets
40035	34	0x22	Incorrect Packets LSR	Read/write	No. of received packets with error
40036	35	0x23	Incorrect Packets MSR	Read/write	No. of received packets with error
40037	36	0x24	Sent Packets LSR	Read/write	No. of sent packets
40038	37	0x25	Sent Packets MSR	Read/write	No. of sent packets
30051	50	0x32	Outputs	Read	Bit is set if value ≠ 0
40053	52	0x34	Analog output 1	Read/write	Value of Analog Output: in mV for voltage output (max 10240) in μA for current output 0 – 20 mA (max 20480) in ‰ for current output 4-20 mA (max 1000)
40054	53	0x35	Analog Output 2	Read/write
40055	54	0x36	Analog Output 3	Read/write
40056	55	0x37	Analog Output 4	Read/write
40057	56	0x38	Analog Output 5	Read/write
40058	57	0x39	Analog Output 6	Read/write
40059	58	0x3A	Analog Output 7	Read/write
40060	59	0x3B	Analog Output 8	Read/write
40061	60	0x3C	Default Output 1 Value	Read/write	Default value of output set when power is on or when watchdog reset occurs
40062	61	0x3D	Default Output 2 Value	Read/write
40063	62	0x3E	Default Output 3 Value	Read/write
40064	63	0x3F	Default Output 4 Value	Read/write
40065	64	0x40	Default Output 5 Value	Read/write
40066	65	0x41	Default Output 6 Value	Read/write
40067	66	0x42	Default Output 7 Value	Read/write
40068	67	0x43	Default Output 8 Value	Read/write
40069	68	0x44	Output 1 Setting	Read/write	Setting of output mode: 0 – output disabled 1 – voltage output 2 – current output 0-20 mA 3 – current output 4-20 mA Caution! For the change to take effect, you must also set the jumper inside the module.
40070	69	0x45	Output 2 Setting	Read/write
40071	70	0x46	Output 3 Setting	Read/write
40072	71	0x47	Output 4 Setting	Read/write
40073	72	0x48	Output 5 Setting	Read/write
40074	73	0x49	Output 6 Setting	Read/write
40075	74	0x4A	Output 7 Setting	Read/write
40076	75	0x4B	Output 8 Setting	Read/write

Registered access

Bit Access

Modbus Address	Dec Address	Hex Address	Register Name	Access	Description
801	800	0x320	Output 1	Read	If voltage or current is greater than 0 then according bit is set.
802	801	0x321	Output 2	Read
803	802	0x322	Output 3	Read
804	803	0x323	Output 4	Read
805	804	0x324	Output 5	Read
806	805	0x325	Output 6	Read
807	806	0x326	Output 7	Read
808	807	0x327	Output 8	Read

Bit access