Room Panel Settings
Accessing any setting menu from the main menu level is possible if the room panel is in the active mode. The OK button together with the Menu button have to be pushed for a time longer than the time value stored in the ENTER_MENU_TIME object. The access to any settings menu is protected by a password stored in the PANEL_PASSWORD object (the default password is 1000).
The current settings menu name blinks on the 14-segment display block.
A different settings menu can be chosen by pushing up and down arrow buttons.
To enter the particular settings menu, push the OK button.
After entering the particular settings menu on the 14-segment display block, the number of the parameter with the lowest number is displayed.
Different available parameters inside the settings menu can be chosen by pushing up or down buttons.
All the parameters are described in more details in particular sections of this User Manual.
Configuration (CONF)
The configuration menu contains objects responsible for the configuration. The main part of all available objects refers to main communication objects such as a baud rate, an address, stop bits, parity bits, and protocol selection. From the configuration menu level the user can change the room panel password or read information about the implemented firmware version. All available parameters are listed in the table below:
|
Parameter Number |
BACnet ID |
Object Property |
Object Name |
Access |
Description |
|---|---|---|---|---|---|
|
1.1 |
Device |
3084 |
BAUD_RATE |
Read & WriteMemory |
48-1152 (*100kbs)
|
|
1.2 |
Device |
3201 |
ADDRESS |
Read & WriteMemory |
Default: 1 |
|
1.3 |
- |
- |
STOP_BITS |
Read & WriteMemory |
1 – one stop bit 2 – two stop bits |
|
1.4 |
- |
- |
PARITY_BITS |
Read & WriteMemory |
0 – disabled 1 – ODD 2 - EVEN
|
|
1.5 |
- |
- |
PROTOCOL |
Read & WriteMemory |
0 – Modbus RTU 1 – Modbus ASCII 2 – BACnet MS/TP |
|
1.6 |
AO 0 |
Present Value |
PANEL_PASSWORD |
Read & WriteMemory |
Default: 1000 |
|
1.7 |
- |
- |
FIRMWARE_VERSION |
Read Only |
Software version |
The CONF menu structure
Device (DEV)
The device settings menu contains objects responsible for global settings. Changing any of particular parameter has influence on different modes and functions implemented in the room panel. Some of the parameters refer to time settings such as the TIME_FORMAT, ENTER_MENU_TIME, EXIT_MENU_TIME, or REFRESH_TIME. In the device settings menu, the user can switch the beeper off, or disable background illumination in the LCD display or the keypad. All available parameters are listed in the table below:
|
Parameter Number |
BACnet ID |
Object Property |
Object Name |
Access |
Description |
|---|---|---|---|---|---|
|
2.1 |
BO 0 |
Present value |
DEVICE CONFIGURATION BEEPER |
Read & WriteMemory |
0-inactive 1-active(def) |
|
2.2 |
BO 1 |
Present value |
DEVICE CONFIGURATION TIME FORMAT |
Read & WriteMemory |
0-24h(def) 1-12h |
|
2.3 |
BO 2 |
Present value |
DEVICE CONFIGURATION TEMPERATURE UNIT |
Read & WriteMemory |
Not supported |
|
2.4 |
BO 3 |
Present value |
DEVICE CONFIGURATION BACKGROUND ILLUMINATION LCD ACTIVE |
Read & WriteMemory |
0-inactive 1-active(def) |
|
2.5 |
BO 4 |
Present value |
DEVICE CONFIGURATION BACKGROUND ILLUMINATION KEYPAD ACTIVE |
Read & WriteMemory |
0-inactive(def) 1-active |
|
2.6 |
AO16 |
Present value |
ENTER MENU TIME |
Read & WriteMemory |
Default value: 2 sec. |
|
2.7 |
AO 17 |
Present value |
EXITED IT TIME |
Read & WriteMemory |
Default value: 5 sec. |
|
2.8 |
AO 18 |
Present value |
EXIT MENU TIME |
Read & WriteMemory |
Default value: 10 sec. |
|
2.9 |
AO 13 |
Present value |
REFRESH TIME |
Read & WriteMemory |
Default value: 2 sec. |
The DEV monu structure
Temperature (TEMP)
The temperature settings menu contains objects referring to the temperature sensor display and temperature control settings. The user is able to switch on/off the temperature sensor value displaying, set the temperature sensor filter, or change the temperature sensor offset. All available parameters are listed in the table below:
|
Parameter Number |
BACnet ID |
Object Property |
Object Name |
Access |
Description |
|---|---|---|---|---|---|
|
3.1 |
AO 4 |
4200 |
TEMPERATURE_CONFIGURATION ACTIVE |
Read & WriteMemory |
0-inactive 1-active(def) |
|
3.2 |
AO 4 |
4202 |
TEMPERATURE_ CONFIGURATION THIRDPOINTACTIVE |
Read & WriteMemory |
0-inactive 1-active(def) |
|
3.3 |
AO 4 |
4003 |
TEMPERATURE_FILTER |
Read & WriteMemory |
Default value: 60 sec |
|
3.4 |
AO 4 |
4205 |
TEMPERATURE_OFFSET |
Read & WriteMemory |
Default value: 0 |
The TEMP menu structure
Humidity (HUM)
The humidity settings menu contains objects referring to the humidity sensor display and humidity control settings. The user is able to switch on/off the humidity sensor value displaying, set the humidity sensor filter, or change the humidity sensor offset. All available parameters are listed in the table below:
|
Parameter Number |
BACnet ID |
Object Property |
Object Name |
Access |
Description |
|---|---|---|---|---|---|
|
4.1 |
AO 5 |
4200 |
HUMIDITY_CONFIGURATION ACTIVE |
Read &WriteMemory |
0-inactive 1-active(def) |
|
4.2 |
AO 5 |
4202 |
HUMIDITY_CONFIGURATION THIRDPOINTACTIVE |
Read &WriteMemory |
0-inactive 1-active(def) |
|
4.3 |
AO 5 |
4003 |
HUMIDITY_FILTER |
Read &WriteMemory |
Default value: 60 sec |
|
4.4 |
AO 5 |
4205 |
HUMIDITY_OFFSET |
Read &WriteMemory |
Default value: 0 |
The HUM menu structure
CO2 (CO2)
The CO2 settings menu contains objects referring to the CO2 sensor display and CO2 control settings. The user is able to switch on/off the CO2 sensor value displaying, set the CO2 sensor filter, or change the CO2 sensor offset. All available parameters are listed in the table below:
|
Parameter Number |
BACnet ID |
Object Property |
Object Name |
Access |
Description |
|---|---|---|---|---|---|
|
5.1 |
AO 6 |
4200 |
CO2_CONFIGURATION ACTIVE |
Read & WriteMemory |
0-inactive 1-active(def) |
|
5.2 |
AO 46 |
4003 |
CO2_FILTER |
Read & WriteMemory |
Default value: 60 sec |
|
5.3 |
AO 6 |
4205 |
CO2_OFFSET |
Read & WriteMemory |
Default value: 0 |
|
5.4 |
AO 19 |
Present value |
CO2_SETPOINT |
Read & WriteMemory |
Default value: 1500 ppm |
Setpoint (SETP)
In the setpoint settings menu, the user has access to the main setpoint objects. It is possible to change the most useful setpoint parameters such as the default setpoint, a low and high setpoint limit, a setpoint step, or a offset range locally from the room panel. The user can also decide if the setpoint value should be displayed in the main menu, or if the setpoint or offset should be changed during the setpoint edition. All available parameters are listed in the table below:
|
Parameter Number |
BACnet ID |
Object Property |
Object Name |
Access |
Description |
|---|---|---|---|---|---|
|
6.1 |
AV 56 |
OUT OF SERVICE |
SETPOINT_CONFIGURATION ACTIVE |
Read & WriteMemory |
0-inactive 1-active(def) |
|
6.2 |
AV56 |
4200 |
SETPOINT_CONFIGURATION EDITABLE |
Read & WriteMemory |
0-inactive 1-active(def) |
|
6.3 |
BO 55 |
Present value |
SETPOINT_CONFIGURATION OPERATING MODE |
Read & WriteMemory |
0-changing offset 1-changing setpoint(def) |
|
6.4 |
BO 56 |
Present value |
SETPOINT_CONFIGURATION SETPOINTDISPLAY |
Read & WriteMemory |
0-changing offset 1-changing effective setpoint(def) |
|
6.5 |
AV 56 |
4202 |
SETPOINT_CONFIGURATION THIRDPOINT_ACTIVE |
Read & WriteMemory |
0-inactive 1-active(def) |
|
6.6 |
BO 57 |
Present value |
SETPOINT_CONFIGURATION FAST_EDIT_MODE |
Read & WriteMemory |
0-inactive(def) 1-active |
|
6.7 |
AV 57 |
Present value |
DEFAULT_SETPOINT |
Read & WriteMemory |
Default value: 210 |
|
6.8 |
AV 56 |
LOW LIMIT |
SETPOINT_LOW_LIMIT |
Read & WriteMemory |
Default value: 180 |
|
6.9 |
AV 56 |
HIGH LIMIT |
SETPOINT_HIGH_LIMIT |
Read & WriteMemory |
Default value: 240 |
|
6.10 |
AV 59 |
Present value |
OFFSET_RANGE |
Read & WriteMemory |
Default value: 30 |
|
6.11 |
AV 56 |
DEFAULT STEP INCREMENT |
SETPOINT_STEP |
Read & WriteMemory |
Default value: 10 |
The SETP menu structure
Fan (FAN)
The objects of the fan settings menu refer to fan configuration settings. The user can change the fan type or decide if the fan status should be displayed in the main menu or not. The editable parameter can determine if the user can change particular fan modes. All available parameters are listed in the table below:
|
Parameter Number |
BACnet ID |
Object Property |
Object Name |
Access |
Description |
|---|---|---|---|---|---|
|
7.1 |
MV 1 |
OUT OF SERVICE |
FAN_CONFIGURATION VISABLE_FAN_CURRENT_SPEED |
Read & WriteMemory |
0-inactive 1-active(def) |
|
7.2 |
MV 1 |
4200 |
FAN_CONFIGURATION EDITABLE |
Read & WriteMemory |
0-inactive 1-active(def) |
|
7.3 |
BO 59 |
Present value |
FAN_CONFIGURATION PART_EDITABLE |
Read & WriteMemory |
0-inactive(def) 1-active |
|
7.4 |
BO 60 |
Present value |
FAN_CONFIGURATION FAST_EDIT_MODE |
Read & WriteMemory |
0-inactive(def) 1-active |
|
7.5 |
AO 21 |
Present value |
FAN_ICON_FLASHING_TIME |
Read & WriteMemory |
Default value: 500 ms |
|
7.6 |
MV 2 |
1602 |
FAN_TYPE |
Read & WriteMemory |
0-0-10 V(def) 1-1-Speed 2-2-Speed 3-3-Speed |
The FAN menu structure
Occupancy (OCCU)
The occupancy settings menu contains objects referring to the occupancy configuration. The user can decide if the current occupancy status should be displayed in the main menu or not. The editable parameter can determine if the user can change the occupancy mode. All available parameters are listed in the table below:
|
Parameter Number |
BACnet D |
Object Property |
Object Name |
Access |
Description |
|---|---|---|---|---|---|
|
8.1 |
MV 4 |
OUT OF SERVICE |
OCCUPANCY_CONFIGURATION VISABLE_OCCUPANCY_CURRENT_STATUS |
Read & WriteMemory |
0-inactive 1-active(def) |
|
8.2 |
MV 4 |
4200 |
OCCUPANCY_CONFIGURATION EDITABLE |
Read & WriteMemory |
0-inactive 1-active(def) |
|
8.3 |
BO 61 |
Present value |
OCCUPANCY_CONFIGURATION FAST_EDIT_MODE |
Read & WriteMemory |
0-inactive(def) 1-active |
The OCCU menu structure