Light Level Control Registers
LLC_SETPOINT_ZONE_1 (40489)
The register contains the setpoint value of the light level for zone 1. By default, the setpoint is 1000 lx.
LLC_SETPOINT_ZONE_2 (40490)
The register contains the quantity of zones to be controlled separately. By default, the register is set to two zones.
LUX_MIN_SENSOR_1 (40494)
The register sets the minimum value of the light level sensor for zone 1. By default, the minimum value is set to 0 lx.
LUX_MIN_SENSOR_2 (40495)
The register sets the minimum value of the light level sensor for zone 2. By default, the minimum value is set to 0 lx.
LUX_MAX_SENSOR_1 (40498)
The register sets the maximum value of the light level sensor for zone 1. By default, the maximum value is set to 3000 lx.
LUX_MAX_SENSOR_2 (40499)
The register sets the maximum value of the light level sensor for zone 2. By default, the maximum value is set to 3000 lx.
LLC_OFFSET (40478)
The register sets the offset value between the control signal on the DALI2 bus in reference to the DALI1 bus. By default, the offset value is set to 0.
LUX_SENSOR_TYPE_1 (40502)
The registers sets the special input mode used to read the signal from the lux level sensor 1. By default, the special input mode is set to 0-10 V.
LUX_SENSOR_TYPE_2 (40503)
The registers sets the special input mode used to read the signal from the lux level sensor 2. By default, the special input mode is set to 0-10 V.
LUX_SENSOR_ENABLE (40506)
The register value enables either lux level sensor:
- bit 0: LUX_SENSOR_1_ENABLE;
- bit 1: LUX_SENSOR_2_ENABLE.
By default, the register is set to bit 1.
LLC_PIR_1_DIMM_TIME (40485)
The register sets the time, which–upon expiring–dims the light in the zone 1 if the presence sensor detects no movement. By default, the time is set to 0 s.
LLC_PIR_2_DIMM_TIME (40486)
The register sets the time, which–upon expiring–dims the light in the zone 2 if the presence sensor detects no movement. By default, the time is set to 0 s.
LLC_PIR_1_DIMM_LEVEL (40481)
The register contains the dimmed light level after counting down the time set in the LLC_PIR_1_DIMM_TIME register. By default, the dimmed light level is set to 20%.
LLC_PIR_2_DIMM_LEVEL (40482)
The register contains the dimmed light level after counting down the time set in the LLC_PIR_2_DIMM_TIME register. By default, the dimmed light level is set to 20%.
LLC_KP_ZONE_1 (40507)
The 32-bit register contains the proportional gain of the PID controller for zone 1. By default, the value is set to 0,021.
LLC_KP_ZONE_2 (40509)
The 32-bit register contains the proportional gain of the PID controller for zone 2. By default, the value is set to 0,021.
LLC_KI_ZONE_1 (40515)
The 32-bit register contains the integral gain of the PID controller for zone 1. By default, the value is set to 0,007.
LLC_KI_ZONE_2 (40517)
The 32-bit register contains the integral gain of the PID controller for zone 2. By default, the value is set to 0,007.
LLC_KD_ZONE_1 (40523)
The 32-bit register contains the derivative gain of the PID controller for zone 1. By default, the value is set to 0,012.
LLC_KD_ZONE_2 (40525)
The 32-bit register contains the derivative gain of the PID controller for zone 2. By default, the value is set to 0,012.
LUX_STATUS_1 (40681)
The read-only register shows the lux light intensity value from the sensor connected to S1.
LUX_STATUS_2 (40682)
The read-only register shows the lux light intensity value from the sensor connected to S2.
LUX_SENSOR_VOLTAGE_1 (40132)
The read-only register shows the voltage value on the S1 special input (expressed in millivolts).
LUX_SENSOR_VOLTAGE_2 (40133)
The read-only register shows the voltage value on the S2 special input (expressed in millivolts).