Module Registers | iC Knowledge Base

Registered Access

Modbus Address	Decimal Address	Hex Address	Register Name	Access	Description
30001	0	0x00	Version/Type	Read	Version and type of the device
30002	1	0x01	Switches	Read	Switches state
40003	2	0x02	Baud Rate	Read/write	RS485 baud rate
40004	3	0x03	Stop Bits & Data Bits	Read/write	No. of stop bits & data bits
40005	4	0x04	Parity	Read/write	Parity bit
40006	5	0x05	Response Delay	Read/write	Response delay in ms
40007	6	0x06	Modbus Mode	Read/write	Modbus mode (ASCII or RTU)
40010	9	0x09	Analog Filtering	Read/write	Analog filtering configuration
40033	32	0x20	Received Packets LSR (Least Significant Register)	Read/write	No. of received packets
40034	33	0x21	Received Packets MSR (Most Significant Register)	Read/write	No. of received packets
40035	34	0x22	Incorrect Packets LSR	Read/write	No. of received packets with error
40036	35	0x23	Incorrect Packets MSR	Read/write	No. of received packets with error
40037	36	0x24	Sent Packets LSR	Read/write	No. of sent packets
40038	37	0x25	Sent Packets MSR	Read/write	No. of sent packets
30051	50	0x32	Inputs	Read	Connected inputs Bit in high state → signal is connected
40052	51	0x33	Outputs	Read/write	Alarms state bit 9 and 10 alarm outputs
30053	52	0x34	Analog 1	Read	Value of Analog Input in mV for voltage inputs in μA for current inputs
30054	53	0x35	Analog 2	Read
30055	54	0x36	Analog 3	Read
30056	55	0x37	Analog 4	Read
30057	56	0x38	Analog 5	Read
30058	57	0x39	Analog 6	Read
30059	58	0x3A	Analog 7	Read
30060	59	0x3B	Analog 8	Read
30061	60	0x3C	Value of 1. Alarm Input	Read	Current values of voltage / current for alarm inputs
30062	61	0x3D	Value of 2. Alarm Input	Read	Current values of voltage / current for alarm inputs
40063	62	0x3E	MAX Alarm Level 1	Read/write	If the analog signal exceeds this value the corresponding alarm flag is set
40064	63	0x3F	MAX Alarm Level 2	Read/write
40065	64	0x40	MAX Alarm Level 3	Read/write
40066	65	0x41	MAX Alarm Level 4	Read/write
40067	66	0x42	MAX Alarm Level 5	Read/write
40068	67	0x43	MAX Alarm Level 6	Read/write
40069	68	0x44	MAX Alarm Level 7	Read/write
40070	69	0x45	MAX Alarm Level 8	Read/write
40071	70	0x46	MIN Alarm Level 1	Read/write	If the analog signal is below this value corresponding alarm flag is set
40072	71	0x47	MIN Alarm Level 2	Read/write
40073	72	0x48	MIN Alarm Level 3	Read/write
40074	73	0x49	MIN Alarm Level 4	Read/write
40075	74	0x4A	MIN Alarm Level 5	Read/write
40076	75	0x4B	MIN Alarm Level 6	Read/write
40077	76	0x4C	MIN Alarm Level 7	Read/write
40078	77	0x4D	MIN Alarm Level 8	Read/write
40079	78	0x4E	Alarm Settings 1	Read/write	Alarm settings 0 – alarm due to the current analog signal value 1 – remember the value of the alarm, until reset by the master via Modbus
40080	79	0x4F	Alarm Settings 2	Read/write
40081	80	0x50	Alarm Settings 3	Read/write
40082	81	0x51	Alarm Settings 4	Read/write
40083	82	0x52	Alarm Settings 5	Read/write
40084	83	0x53	Alarm Settings 6	Read/write
40085	84	0x54	Alarm Settings 7	Read/write
40086	85	0x55	Alarm Settings 8	Read/write
40087	86	0x56	Input 1 settings	Read/write	Analog input mode: 0 – input disabled 1 – voltage 0 V to 10 V 2 – voltage -10 V to 10 V 3 – voltage 0 V to 1 V 4 – voltage -1 V to 1 V 5 – current 4 mA to 20 mA 6 – current 0 mA to 20 mA 7 – current -20 mA to 20 mA To change the input mode you must to set jumper inside of module.
40088	87	0x57	Input 2 settings	Read/write
40089	88	0x58	Input 3 settings	Read/write
40090	89	0x59	Input 4 settings	Read/write
40091	90	0x5A	Input 5 settings	Read/write
40092	91	0x5B	Input 6 settings	Read/write
40093	92	0x5C	Input 7 settings	Read/write
40094	93	0x5D	Input 8 settings	Read/write
40095	94	0x5E	Output 1 settings	Read/write	Alarm output settings 0 – output is set by PLC +1 – value from input 1 +2 – value from input 2 +4 – value from input 3 +8 – value from input 4 +16 – value from input 5 +32 – value from input 6 +64 – value from input 7 +128 – value from input 8 +256 – Output is set if value is greater than Alarm Value (register 40097 or 40098) („cooling") +512 – Output is set if value is less than Alarm Value ( register 40097 or 40098) („heating") +1024 – The lowest value from selected inputs +2048 – The greatest value from selected inputs (if not select either of the two above options than is used average value of selected inputs)
40096	95	0x5F	Output 2 settings	Read/write
40097	96	0x60	Alarm Value 1	Read/write	Alarm value for outputs
40098	97	0x61	Alarm Value 2	Read/write	Alarm value for outputs
40099	98	0x62	Alarm Hysteresis 1	Read/write	The hysteresis value for alarm outputs
40100	99	0x63	Alarm Hysteresis 2	Read/write	The hysteresis value for alarm outputs

Registered access

Bit Access

Modbus Address	Dec Address	Hex Address	Register Name	Access	Description
801	800	0x320	Input 1	Read	Set when the input is connected
802	801	0x321	Input 2	Read	Set when the input is connected
803	802	0x322	Input 3	Read	Set when the input is connected
804	803	0x323	Input 4	Read	Set when the input is connected
805	804	0x324	Input 5	Read	Set when the input is connected
806	805	0x325	Input 6	Read	Set when the input is connected
807	806	0x326	Input 7	Read	Set when the input is connected
808	807	0x327	Input 8	Read	Set when the input is connected
817	816	0x330	Alarm 1	Read	Alarm state 1
818	817	0x331	Alarm 2	Read	Alarm state 2
819	818	0x332	Alarm 3	Read	Alarm state 3
820	819	0x333	Alarm 4	Read	Alarm state 4
821	820	0x334	Alarm 5	Read	Alarm state 5
822	821	0x335	Alarm 6	Read	Alarm state 6
823	822	0x336	Alarm 7	Read	Alarm state 7
824	823	0x337	Alarm 8	Read	Alarm state 8
825	824	0x338	Digital Output 1	Read/write	State of digital output 1
826	825	0x339	Digital Output 1	Read/write	State of digital output 2

Bit access